Author: lsvop

About lsvop

I'm an occupational therapist with a special interest in assistive technology. I'm also a avid hobby woodworker who is trying to learn Greene and Greene furniture. I also use my woodworking skills to make mounting and customised seating for people with disabilities to use with assistive technology.

Shaker style cabinet

cabinet.jpg

There used to be a sink at that spot where this cabinet now stands. The sink was removed but the pipes, threaded rod and other fasteners that hold the sink to the wall are still there. My operations department, requested that occupational therapy help them make a cupboard. As the occupational therapist, aka me, is nice and obliging, I obliged.

I decided to make the cabinet in the Shaker style. (You all know G&G is my preferred style) Something simple that I can finish in a week (since I am leaving the company), yet nice enough for others to remember me by.

All the joints are dado joints. The frame of the door is mortise and tenon joint. The panel is booked matched and stained for contrast. If I were to improve the cabinet in future,  perhaps I’ll add in a turned door knob.

Study Table

I thought it was about time I got myself a new study table. The old one was a standard compressed wood one the was discarded by the person I bought my flat from.

My brief was simple. I wanted a lot of storage, since my table top is always such a mess. I need as many drawers as I could possibly have. I have a plank of Kapur left over from another project, so I just got to use that up.

I did the drawers first. The carcass was put together with proud fingerjoints. A common Greene and Greene feature. The drawer pulls were inspired by Darrel Pert. I used the design technique that Darrel shared somewhere (can’t recall where I read it). He said to look at a design for inspiration, go do something else for a week or so, then come back and design your own design. I found my drawer pull to be somewhat different from what Darrel’s, although it was easy to see where the inspiration came from. The drawers are all made of solid pine except the base. I could have put it some proud finger joints on the drawer front but didn’t. It would have been better if I did.

The table itself is of frame and panel construction. The legs are glued up pieces, really bulky. They are too thick in proportion to the top. To make them appear slimmer, without compromising strength, I shaped the two exposed sides to a slight convex. The panels are pine wood stained elbony and then sanded down. They got the cloud lift design. I felt that this would give it some contrast  to the frame but still blend it with the frame.

The table top is Kapur wood framed by pine. I also installed a  keyboard drawer so that the height of the keyboard fits my body.

Electric keyboard stand

Just finished a stand for an electric keyboard. It’s made of recycled lumber from a crate, so material cost is less than $10 for some varnish, stain, and sandpaper.

Someone donated a keyboard with a broken stand to the nursing home. My executive director simply asked if I could repair the stand. I couldn’t resist the urge to build a new one.

The vertical post are 4 pieces of lumber glued together with miter joints, the kind that was used in Stickly furniture. The feet of the stand are actually simple boxes. Because of the Stickly design, I am able to threat the wire for the pedals through the hollow post, making the entire thing look a little neater.

As I said, the wood came from a crate. This explains the large number of knots in pine, but it adds character.

This stand was dyed elbony and finished with 5 coats of rubbing varnish. The patients I was working with learned how to make wooden pegs, peg screw holes and trim them flush, sanding, dye the wood and use rub on varnish.

 

 

2015-10-07 17.03.01 2015-10-07 17.03.33 2015-10-07 17.03.40 2015-10-07 17.04.33 2015-10-14 13.44.44 2015-10-14 13.45.03 2015-10-14 13.45.21 2015-10-14 13.45.35

Wash Basin

I was inspired to do a wash basin for my toilet for quite some time already. I made the side, a little bit of the top; various parts were lying in my workshop at various degree of completion. The kick in the butt came when my neighbor living on the floor below me complained that my toilet floor was leaking. I needed to hack previous sink for the renovation.I can’t be living without a sink in the toilet, so I had to get my act together to finish this piece of art.

This piece is made of Burmese teak, which I read is used to make boats. The cabinet and doors are frame and panel construction. The joints are glued with titebond 3 and held with screws which are then covered by Ebony square pegs. Ebony square pegs are a hallmark of Green and Greene furniture design. The sink is actually a square box with proud finger joints. The sink sits on a flat top with breadboard end on one side to keep everything flat, Because of the urgency that I needed this piece of furniture, I did not do any cloud lift.  The entire piece is finished with 3 layers of epoxy.

Nativity scene

nativity scene

As some of you who follow this blog of mine already know, I’m working in a psychiatric nursing facility. No, I’m not a nurse. I’m an occupational therapist.  One of the most beautiful things about my job is that I can do woodworking (a hobby that I truly love) and get paid for it.

The idea came for a nativity scene during one of the welfare committee meetings and as you probably guessed, I was tasked to make one. Buying one would be too expensive for the charitable nursing home.

I found templates for the figurines on the internet and started to design something based on silhouette concept. I worked with my patients to paste the template on the wood, saw it out with a scroll saw, sand it and finally finished it with a coat of varnish.

My director thought I salvage the base from someone’s table top and was surprised that it came from rough sawn lumbar. After the nativity scene was displayed, my patients gathered around the display for tea and to admire their handy work.

Rocking chair – work in progress

 

20140610_165804_Android 20140610_165755_Android 20140610_165748_Android

 

I am an occupational therapist working with patients with mental health problems in a psychiatric nursing home.. One of the main problems that the people I work with face is their poor cognition. Their ability to reason in a coherent manner, short term memory, reasoning ability and the ability to learn new task is affected due to their condition of schizophrenia, low IQ, among other diagnosis.

Their cognitive deficits also affect their psychosocial aspects as well. Because they are achieving much less than others, issues such as self esteem, self concept, self efficacy are also a problem. They may see themselves as being unable to achieve anything except whatever to take whatever handouts that the healthcare providers or volunteers give. They say something is too difficult even before they try because they lack the confidence to even try.

After analyzing these problems, I decided to work with them to build a rocking chair. I thought that building a rocking chair would let them see themselves as achievers. Inspiration for the design was gathered from the Maloof Rocking chair and that of  the Shaker rocking chair. I did not have a clear design on paper to work with. Instead what I did was to make a plywood model of the rocking chair, test it for comfort, before I sketch the curves on the plywood. After one side is done, my friendly router bit did the work of shaping the other side, using the first side as a template.

My patients did the sanding, lots of it. One or two of them help to drive in the screws during assembly. All of them felt that they contributed to the making of the chair in some way and they were all smiles when they sat on the chair and started rocking. One of them was heard exclaiming, “we succeeded, we succeeded!”

While the material cost of the rocking chair is really cheap (S$65), the amount of self esteem it brings to the patients is through the roof. Woodworking is indeed a good activity for patients with mental health issues.

 

Creative marbling machine prototype

There are many marbling machines on the internet. Most of them are table top. Shawn Yeo, who founded VINCO, an educational company that specializes in  creating environments that develop students to be independent learners, leaders and thinkers through tinkering approached me for this project.

Shawn explained the project to me enthusiastically. He wanted a marbling kit which could be attached to a whiteboard via a magnet. A marbling machine allows a marble to go through a set of obstacles, making a little noise in the process. They are also very interesting to watch.

The challenge of this project is the very very thin pieces. There are a lot of parts that are only 3mm thick.

Wave like wooden structure

This wave like structure was interesting to make. The shape was first cut on a scroll saw before being glued together so that the front and back are identical.

Diagram showing 2 grooves routed on a back of a maze like obstacle.

These 2 grooves are where the magnet will sit in.

Maze like structure

Parts were individually cut before gluing it all together with wood glue. Realised that the trick to doing 3mm cuts on a table saw is to cut on the other side, not between the blade and the fence.

DSC_1091

With the circular part only 3mm thick, it was a feat to cut. The trick, use a very slow speed, <500rpm on a drill press. I did spoil quite a number of them before getting it right.

Triangle shaped block with grooves on each side.

The triangle has a drain on each side.
Note the very thin front.

DSC_1068

This was quite interesting to make.I had to drill the hole at exactly the correct spot, then shape the rounded top on the router table.

DSC_1090 DSC_1087 DSC_1085 DSC_1082 DSC_1075 DSC_1069 DSC_1066 DSC_1065 DSC_1047 DSC_1034 DSC_1033

End Grain Pop Cake Holder by a Woodworker in Singapore

A friend of mine wanted to make pop cakes for her department year end party. She thus needed a pop cake stand. She searched the web and found a simple stand costing $50. It was a simple block of wood with holes and then spray painted white. She sent me a link and asked if I could replicate it.

“Of course I can, but why would I?” was my instant reply. So I designed a one that I could call my own design, taking inspiration from the end grain cutting board.

The main board was made from the end grains of pine wood. This is frame with a teak border. Lengthwise, the teak border sits in a dovetail groove. This gives it space to expand and contract as wood naturally does. The ends tongue and grooved and held together with spots of glue and panel pins which hold them in place but still give them sufficient space to expand and contract.

So there it is. An end grain pop cake holder. I hope she likes it.
DSC_1111

Balcony Table and Stool Set for Sale in Singapore

One table and two stools

Greene and Greene inspired table and stool set

This beautiful and unique table and stool set was inspired by the cloud lifts of Greene and Greene furniture. This piece is made from solid Burmese Teak which is a strong and lasting wood. It’s nice golden brown adds warmth to any room. The combination of good quality teak with the beauty of G&G cloud lifts  has a special grace that beckons you to sit and have coffee. The legs are inlayed with purpleheart which gives a nice complement to the golden brown teak wood. The joints at the legs are solid mortise and tenon joinery. All surfaces are rounded and hand sanded to 240 grit making the edges inviting to touch.

Dimensions
The table is 710mm high and has a top 595mm in diameter.
The stool is 460mm high and 335mm in diameter.

Price
Table: S$600
Stool: S$400
Entire set: $1400
Please note that this is NOT outdoor furniture. Do NOT use in wet weather.

Stool with nice wood grain

Teak wood, nice grain

Stool with clould lifts

Note the shape of the legs

DSC_0441

Cloud lift

Cloud lift

Cloud lift

Table with view of grain

Like the wood grain of the table top

Table top showing wood grain

Like the wood grain of the table top

Table with legs

Can you see the Purpleheart inlay?

Set of table and stool

Isometric view

Side view

Side view

Table and stool set taken from a lower angle

Photo taken from a lower angle

DSC_0426 DSC_0425 DSC_0424 DSC_0423 DSC_0422 DSC_0421 DSC_0420
Burmese Teak Stool and Table Set. Price: $1400

Burmese Teak Stool and Table Set. Price: $1400

DSC_0415 DSC_0414
Table and stool with cloud lift pattern

Note the Greene and Greene inspired cloud lift pattern

Nice balcony table and stool

Will look good in your balcony

top view of table and stool

Top view

Picture of table and stool set taken from a low angle

Front view

One table and two stools

Greene and Greene inspired table and stool set

This slideshow requires JavaScript.